Timber & Framing
Lumber Calculator
Calculates board feet and linear feet of lumber for any project
Updated May 13, 2026 · Live
What this tool does
Calculates board feet and linear feet of lumber for any project. 2x4, 2x6, 2x8, 2x10.
Formula Used
People also use
How the lumber calculator works
Calculates board feet and linear feet of lumber for any project. 2x4, 2x6, 2x8, 2x10. The calculator takes your dimensions and supplier rates, applies a standard US construction formula, and returns a quantity with an indicative cost. Every figure is an estimate — site conditions always move the final number.
Typical US timber and framing wastage
Dimensional lumber wastage runs 10% on straight cuts, 15% on angled or notched framing. Order at lengths that minimize splicing — a 16 ft joist often nets cheaper than two 8 ft pieces with a hanger. Our defaults reflect common US trade allowances, and can be adjusted upwards for non-standard geometry or downwards where experience supports a lower figure.
What this tool does not do
It does not replace a professional quote, factor regional pricing, assess structural adequacy, or confirm building code compliance. Those remain the responsibility of a suitably qualified designer, engineer, or your local building official.
On-site considerations for lumber
Check grade stamps on every piece — structural framing must be graded to NLGA or WCLIB rules (#2 or better for joists, studs, and rafters). KD-HT (kiln-dried, heat-treated) or S-Dry stamps confirm moisture content under 19% at mill.
Codes and compliance
Framing for one- and two-family dwellings follows IRC R602–R802 span tables. Engineered or unusual layouts need stamped calculations from a licensed structural engineer; your building department will ask for them. When in doubt, file a pre-application question with your local building department — early clarity is cheaper than a corrective inspection.
Before you order
Use pressure-treated lumber (Ground Contact UC4A for posts, Above Ground UC3B for joists) wherever the wood touches concrete or sees moisture. The premium is small relative to the cost of a rebuild. Cross-checking the calculator’s output against a supplier quote helps catch differences in pricing assumptions — ask for exact product specifications (grade, finish, batch number) and confirm delivery timescales against your programme.
Adjusting the defaults
Every input in this calculator is editable. Enter your own dimensions, supplier prices, and wastage allowance — the output recalculates instantly. If the defaults feel off for your region or project type, your own numbers always override them.
Using this lumber calculator alongside other BuildMetricLab tools
This calculator works best as part of a planning workflow. Pair the quantity with our project contingency, labor-hours, and material-cost calculators to build a complete estimate before you pick up the phone to a supplier. All BuildMetricLab tools run entirely in your browser — no sign-up, no data sent anywhere, and every formula is shown on-page so you can audit the math.
Sources & methodology
This calculator computes board feet and linear feet for a given lumber piece using the standard formula: Board Feet = (Thickness_in × Width_in × Length_ft) / 12, where thickness and width are nominal dimensions in inches and length is in feet. Linear feet are calculated as Length_ft × Quantity, and total board feet scale the per-piece result by the same quantity. Note that the input fields label thickness as the narrower face dimension and width as the wider face, so entering a 2×4 requires placing 2 in the thickness field and 4 in the width field.
Frequently asked questions
Are lumber calculator results accurate enough to order materials?
Use them as a starting estimate only. Verifying the final quantity with your supplier or contractor before ordering is good practice — site conditions, wastage and cut-offs all affect the true figure.
What wastage percentage should I use?
The calculator defaults to the typical US trade allowance for timber & framing. Increase it for complex cuts, awkward shapes, or first-time DIY. The default wastage allowance reflects common trade practice; values lower than the default may underestimate offcuts.
Does this replace professional advice?
No. This tool is a planning estimator. For work that affects structure, building code compliance, gas, electrical, plumbing, or drainage to a public sewer, consult a licensed contractor or design professional.
Can I change the unit prices?
Yes — every price field is editable. Plug in your supplier's quote to get a total that matches your project.
Related tools
Calculators from other categories that planners often reach for next.