Drainage & Earthworks
Crushed Stone Base Calculator
Calculates crushed stone or gravel base material for paver, driveway, or shed pads
Updated May 13, 2026 · Live
What this tool does
Calculates crushed stone or gravel base material for paver, driveway, or shed pads.
Formula Used
People also use
How the crushed stone base calculator works
Calculates crushed stone or gravel base material for paver, driveway, or shed pads. The calculator takes your dimensions and supplier rates, applies a standard US construction formula, and returns a quantity with an indicative cost. Every figure is an estimate — site conditions always move the final number.
Typical US drainage and earthworks wastage
Excavated soil bulks up 15–35% when lifted, so dumpster capacity fills faster than the in-place volume suggests. Plan a 1.25× swell factor when sizing haul-off. Our defaults reflect common US trade allowances, and can be adjusted upwards for non-standard geometry or downwards where experience supports a lower figure.
What this tool does not do
It does not replace a professional quote, factor regional pricing, assess structural adequacy, or confirm building code compliance. Those remain the responsibility of a suitably qualified designer, engineer, or your local building official.
On-site considerations for crushed stone base
Excavations over 4 ft deep need shoring, sloping, or benching per OSHA 1926 Subpart P. Call 811 (Dig Safely) at least 48–72 hours before any excavation to mark utilities.
Codes and compliance
Foul and storm drainage follows the IPC and local stormwater rules; many jurisdictions require permits for tie-ins to public sewer or storm drains. Dry wells (drywells) need a perc test to size correctly. When in doubt, file a pre-application question with your local building department — early clarity is cheaper than a corrective inspection.
Before you order
Buy SDR-35 or Schedule 40 PVC drain pipe in standard 10 ft or 20 ft lengths with gasketed bell joints. Cutting short pieces on site wastes material and fittings. Cross-checking the calculator’s output against a supplier quote helps catch differences in pricing assumptions — ask for exact product specifications (grade, finish, batch number) and confirm delivery timescales against your programme.
Adjusting the defaults
Every input in this calculator is editable. Enter your own dimensions, supplier prices, and wastage allowance — the output recalculates instantly. If the defaults feel off for your region or project type, your own numbers always override them.
Using this crushed stone base calculator alongside other BuildMetricLab tools
This calculator works best as part of a planning workflow. Pair the quantity with our project contingency, labor-hours, and material-cost calculators to build a complete estimate before you pick up the phone to a supplier. All BuildMetricLab tools run entirely in your browser — no sign-up, no data sent anywhere, and every formula is shown on-page so you can audit the math.
Sources & methodology
This calculator estimates the volume and weight of crushed stone or gravel needed for a base layer under pavers, driveways, or shed pads. Volume is derived from the formula (Area × Depth) / 27 to convert cubic feet to cubic yards, then multiplied by a compacted density in tons per cubic yard to produce a weight in tons. A typical density range for crushed stone is 1.35–1.5 tons per cu yd; the tool applies this conversion entirely within US imperial units. Total material cost is calculated by multiplying the estimated weight in tons by a user-supplied price per ton.
Frequently asked questions
Are crushed stone base calculator results accurate enough to order materials?
Use them as a starting estimate only. Verifying the final quantity with your supplier or contractor before ordering is good practice — site conditions, wastage and cut-offs all affect the true figure.
What wastage percentage should I use?
The calculator defaults to the typical US trade allowance for drainage & earthworks. Increase it for complex cuts, awkward shapes, or first-time DIY. The default wastage allowance reflects common trade practice; values lower than the default may underestimate offcuts.
Does this replace professional advice?
No. This tool is a planning estimator. For work that affects structure, building code compliance, gas, electrical, plumbing, or drainage to a public sewer, consult a licensed contractor or design professional.
Can I change the unit prices?
Yes — every price field is editable. Plug in your supplier's quote to get a total that matches your project.
Related tools
Calculators from other categories that planners often reach for next.